While there are many things to consider when shopping for a new trailer, one thing's for sure: your local Load Rite Dealer stands ready to find the Rite trailer for your needs and lifestyle. Use the information in this section to learn more about features that matter when choosing a new boat trailer.
| Features | Series Standard |
| Additional Information | |||||
|---|---|---|---|---|---|---|---|---|
| Tires | Bias-Ply | * | - | *Aluminum & Galvanized Skiff Elite models, pontoon models, and models with leaf spring suspension have bias-ply tires. | ||||
| Radial | * | *Aluminum & Galvanized Skiff Elite models, pontoon models, and models with leaf spring suspension have bias-ply tires. | ||||||
| Lighting | Incandescent | - | ||||||
| LED | ||||||||
| Roller Systems | Steel Roller Bar Thermo Plasticized Rubber | - | ||||||
| Fully Articulating Thermo Plasticized Rubber | - | |||||||
| ALUMINUM BUNK SYSTEMS | Solid Wood* | - | *Solid wood bunks with a beveled edge. | |||||
| AB Style* | - | *Pivoting bunks mounted on galvanized steel support tubes. | ||||||
| ALUMINUM BUNK SIDE GUIDES | Side Guide Tubes | ** | * | *Elite tandem and Elite triaxle aluminum models **Elite single axle and all 5 STARR aluminum models available as an option. | ||||
| FENDER STEPS | Extruded Aluminum | - | ||||||
| TAILLIGHT MOUNT | Exposed Taillights | - | ||||||
| Integral Taillight Protection | - | |||||||
| WARRANTY | 2 Plus 3 YearCoupler to Taillight* | *Visit the Warranty Page to review.All Load Rite Trailers carry a 5-year structural frame warranty. | ||||||
Know before you tow!
WARNING: Before towing any trailer, be sure to read and familiarize yourself with all documentation and warnings supplied by the manufacturer. Every Load Rite trailer is shipped from the factory with an Owner’s Manual. Make sure you receive a hard copy from your dealer, or download here.
Rollers offer the ease of quick roll-off launching and drive-on loading*. Because our rollers articulate, they act as their own guide for centering your boat and are the ideal support system for those launching and loading in poor ramp or tidal conditions. However, not every boat can be towed on a trailer equipped with rollers. Check with your dealer or boat manufacturer to see what is recommended for your boat.
(*Drive on loading is not recommended with aluminum I-beam frame roller trailers.)
Bunk trailers are preferred where launch ramps are good, tides are at a minimum, and currents and wind are not factors. When adjusted optimally, Bunk Trailers provide good support for boat storage and require little adjustment once set for a particular boat. Load Rite recommends Quick-Slide® bunk covers on allapplications where bunks would be in direct contact with a metal hull. This will prevent moisture from being trapped in bunk carpet fibers and possiblycausing a corrosive environment.
TRADITIONAL V-BUNK AND CONTINUOUS BUNK
Traditional V-Bunks are used on our smaller trailers (up to 22 feet) and built to be submerged allowing your boat to float during launch and load. Continuous bunk models can handle much heavier loads.
AB BUNK TRAILERS
AB bunk models perform like V-Bunks but can support much greater weight than wood alone. With the AB system, traditional bunks are mounted atop steel support tubes and can pivot left to right, giving tremendous hull support.
S.A.® BUNK TRAILERS
S.A.® Bunk Trailers are a Load Rite exclusive. S.A.® Bunks combine the smooth articulation of our roller designed trailers with the abilities and characteristics ofa conventional bunk trailer. Our self-adjusting bunk trailers give increased support to the boat with more surface area and can be adjusted to fit in a minimal amount of time.
Brakes laws vary from state to state, but Load Rite highly recommends equipping your trailer with brakes on each axle. All state laws refer to the Gross Vehicle Weight Rating (GVWR) to determine brake requirements. The GVWR equals the combined total weight of your boat, personal gear and, of course, the trailer. Check the local brake laws with your DMV for the latest requirements.
| Features | Standard |
| Additional Information | |||||
|---|---|---|---|---|---|---|---|---|
| Corrosion Resistance | Resistant | * | *Galvanized steel is hot dipped in a molten zinc solution to completely coat and provide corrosion resistance and self-healing abilities. | |||||
| Trailer Type | Roller | * | *Aluminum Roller models are limited to float-off/float-on launching and loading. | |||||
| Bunk | ||||||||
| Capacity | 18,000 lb. Limit | |||||||
| 18,000 lb. Limit | ||||||||
Most of our model listings include columns of specifications including “Bow Eye to Transom Minimum“, “Bow Eye to Transom Maximum“, and “Width Between Fenders“, and “Overall Width“. This information should help our dealers better approximate how a boat will sit on a trailer.
The diagrams display the correlation between the boat hull and trailer dimensions.
Many trailers have a great amount of adjustment in the support structure. Adjustment to either extreme may require moving the axles to maintain tongue weight in the 7% to 10% ideal range for most trailers
“A” Bow Eye to Transom Maximum | “B” Bow Eye to Transom Minimum | “C” Rear to Angle Support
Proper towing habits and regular maintenance extends the life of your trailer and keeps you, your passengers and your payload safe. Follow these important towing, storage, maintenance and safety tips to get maximum enjoyment from your Load Rite trailer.
Refer to tow vehicle capabilities supplied by the manufacturer and compare with trailer requirements.
A tow vehicle must be rated for the full GVWR of the trailer being towed
A hitch assembly rated must be rated for the full GVWR of the trailer being towed
Match tow ball to the coupler / actuator requirement (2” or 2-5/16”) depending upon trailer capacity. Check with your dealer.
18” to 21” from the ball centerline to the ground. Adjust by using an offset drawbar.
4 or 5 pin flat pigtail connector if no brakes or surge brake equipped, and 7 pin round if Electric Over Hydraulic (EOH) brake equipped.
Required on models with electric or Electric Over Hydraulic (EOH) braking systems
To determine the load capacity requirement of your tow vehicle, refer to the Vehicle Identification Label attached to the trailer on the left frame rail just behind the tongue junction. It will display the maximum load-carrying capacity of the trailer. It is required to show the Gross Vehicle Weight Rating (GVWR) which is the load-carrying capacity plus the weight of the trailer itself. It is the trailer operator’s responsibility to ensure that the total weight of the boat, engine fuel, water, gear and trailer do not exceed the GVWR capacity.
If you don’t know the correct weight of your boat and engine, don’t guess; have it weighed. This usually can be done at a local lumber yard, feed and fertilizer store, quarry, truck weigh station, etc. Take the total weight of the rig and subtract the trailer dry weight that is noted on the VIN sticker.
Be especially careful not to overload the trailer by putting heavy baggage, camping gear, etc., in the boat while traveling. If you must carry such equipment in your boat while trailering, take this into consideration at the time of purchase and go to the next larger-size trailer.
Know before you tow!
WARNING: Before towing any trailer, be sure to read and familiarize yourself with all documentation and warnings supplied by the manufacturer. Every Load Rite trailer is shipped from the factory with an Owner’s Manual. Make sure you receive a hard copy from your dealer, or download here.
| Coupler, hitch and hitch ball are of the correct size and that all ratings match | |
| Coupler is safely secured to tow ball and safety chains are attached to the vehicle hitch | |
| Check all trailer fasteners for proper tightness | |
| Boat or other cargo is securely tied down to trailer front and rear (winch cable or strap is not a tie down) | |
| Wheel lug nuts are properly tightened to 85 to 90 lb./ft. of torque | |
| Wheel bearings are properly adjusted, maintained, and lubricated | |
| Brake fluid reservoir is topped off | |
| If trailer is equipped with brakes, they are properly adjusted and working | |
| Load is within maximum carrying capacity of the trailer and is properly balanced on the trailer | |
| Tongue weight does not exceed 5% to 7% of the total trailer load | |
| Tires are properly inflated to the maximum indicated tire sidewall pressure when cold | |
| All trailer lighting is working properly | |
Be prepared. Plan ahead. Bring tools and spares.
JACK AND LUG WRENCH
Make sure to carry a jack and lug wrench that will work on a trailer. The jack and lug wrench that came with the tow vehicle may work on your trailer, but don’t count on it. If using a hydraulic bottle jack, use a block of wood between the top of the jack and the trailer frame. Carry a plank to use below the jack in case of unstable ground.
SPARE PARTS
Make up a special “trailer kit” and to carry on all trips. This kit should include a spare wheel and tire, jack, lug wrench, wheel chocks, extra line (for tie-downs and winch), extra light bulbs, bearing grease and a grease gun, wheel bearings and seals, and road flares.
Trailer laws addressing requirements such as brakes, lights, safety chains, licensing, etc., vary by state. It is the responsibility of the trailer ownerto make sure your trailer fully complies with motor vehicle the laws in your jurisdiction. Failing to properly use or maintain your trailer can result in serious accidents, injuries and even death. Your local trailer dealer can assist you in this regard. If you are unsure, contact your state motor vehicle department for full information before selecting a trailer.
The total weight of your boat, engine, fuel, water and gear must not exceed the trailer’s maximum load carrying capacity. Overloading a trailer can cause serious injury, property damage, or even death. Note: Maximum load carrying capacity is the Gross Vehicle Weight Rating (GVWR) less the weight of the empty trailer. This information is imprinted on the foil VIN sticker on the left frame rail of every Load Rite trailer.
Improper tongue weight on the tow vehicle hitch ball can cause loss of control of the tow vehicle and result in serious injury, property damage, or even death. Depending upon trailer model, proper tongue weight should be adjusted to 5% to 7% of GVWR when fully loaded.
Improper adjustment of boat supports or improper positioning of the boat on the trailer may cause damage to your boat hull, personal injury, or even death. Contract with your dealer for proper trailer adjustment.
Serious injury, property damage, or even death can result if the total weight of your loaded trailer exceeds the rated capacity of the hitch on your tow vehicle, or the rated towing capacity of the tow vehicle. Consult your tow vehicle manufacturer to determine the towing capacity of your vehicle and hitch.
Failure to properly attach safety chains or cables between your trailer and tow vehicle can result in a run-away trailer should the trailer coupler become detached from the hitch, and could result in property damage, personal injury, or even death.
Failure to properly engage the tow ball in the coupler ball socket and securely lock the coupler latch mechanism can cause the trailer to become detached from the tow vehicle while traveling, which may result in property damage, personal injury, or even death.
Failure to replace coupler or latch assembly if either shows any evidence of wear or damage can result in property damage, personal injury, or even death.
To reduce the risk of property damage, personal injury, or even death, make certain that all trailer lights are in proper working order.
Maintain proper torque on lug nuts or wheel bolts. Failure to do so may result in property damage, personal injury, or even death. Lug nuts should be tightened to 85 – 95 lb./ft. of torque. Keep wheel bearings lubricated. Failure to properly lubricate bearings may cause failure and possible wheel loss resulting in property damage, personal injury, or even death.
Keep tires properly inflated. Failure to maintain correct pressure may result in tire failure and loss of control resulting in property damage, personal injury, or even death.
To ensure overall safety, never exceed 65 MPH while towing a trailer. Trailer brakes must be maintained in good working condition. Loss of adequate braking could result in property damage, personal injury, or even death.
Failure to tie down the bow independently from the winch line could allow your boat to shift while traveling, causing loss of control of the tow vehicle and resulting in property damage, personal injury, or even death.
To reduce the risk of serious injury or even death, do not step inside or on the trailer frame during launching or loading procedures.
To reduce the risk of serious injury or even death should the winch strap, cable or hook fail, always stand to one side when winching the boat onto your trailer.
Your trailer will look better and last longer if you rinse it off with fresh water several times a year. If your trailer is used in salt water, the trailer should be rinsed off after every trip. An annual washing with a mild detergent will help to keep your trailer bright and clean. Avoid wax on a galvanized surface. Do not store when wet. Air drying in a humid environment can promote oxidation of surfaces. Always tow your trailer after washing to aid in drying.
Some insurance policies do not provide coverage when towing a trailer. Check your policy, or call your insurance agent, to be sure you are fully covered.
When your trailer will not be in use for several months, you can ensure that it will continue to provide good performance when you next use it by taking the following steps before storing:
| BEFORE USING YOUR TRAILER AGAIN... | |
|---|---|
| Check tire pressure. Inflate to maximum pressure as indicated on the sidewall. Inspect for dry rot. Replace as necessary. | |
| Check brake fluid level. | |
| Lubricate the bearings. | |
| Retighten winch line and tie-downs. | |
| Remove blocks and return trailer to ground. | |
| Secure to tow vehicle and inspect lighting for proper function. | |
Make certain the tow vehicle is equipped with a proper harness connection to avoid overloading circuits. With annual maintenance, remove light lenses and spray metal components with WD40′ or apply a light coating of petroleum jelly. Always carry spare light bulbs.
To determine the proper tire size for your trailer model, refer to the VIN certification plate located on the front left side of your trailer. This plate will also state the proper tire rim. There is also a tire placard in the same proximity.
Recommended air pressure can also be found on the VIN certification plate, tire placard, and it will be molded on the tire. Always run at full pressure as indicated on tire sidewall.
Should your certification plate be damaged, your dealer can help you in determining the proper tire and rim size.
When jacking up your trailer to change tires, follow the same procedure that you used in checking hub bearings.
Load Rite recommends you add grease regularly for best bearing life. Load Rite uses components that make adding grease a simple process. The trailer hub bearing cap should be metallic and will have either a rubber plug in the center or an exposed grease fitting.
To add grease follow these directions: Remove the rubber plug to expose the grease fitting. Apply grease gun nozzle to the fitting and add grease. Used, contaminated grease will flow toward you around the gun nozzle. Catch in a rag and discard.
-OR-
Apply grease gun nozzle to the exposed fitting and add grease. Used, contaminated grease will expel out the back of the spindle either into or atop the axle tube. If visible, wipe away and discard.
Both of these systems allow grease to be added without damage to the inner seal.
If your trailer came with “bearing buddies” (clear plastic, exposed grease fitting, spring loaded internal plate) grease can be added to top off to capacity. It is possible to overfill and damage the inner grease seal. To replace grease the hub must be disassembled. It is NOT recommended to replace the bearing covers on your Load Rite with “bearing buddies” unless they were original equipment. “Bearing buddies” are not currently used on any Load Rite product, and only appear on some pre-2005 small trailers under 1500 lb. capacity.
CAUTION – Leave the trailer connected to the tow vehicle with tow vehicle parking brake set and wheels chocked. Trailer must be on level ground.
To jack up your trailer, first block the wheel on the opposite side, both front and back.
Note: It is highly recommended that the following service be performed annually. Remove each wheel and hub. Visually inspect and replace the following items as necessary: bearings, bearing races, seals and brake components. Always reassemble with a new seal and retainer, repack with fresh clean grease. All work should be performed by a qualified mechanic.
NOTE: All bearing protector caps are designed to fit tightly into the hub. Take care in aligning the protector cap with the hub.